View MCR106_1278034.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

UTC MCR106
REVERSE BLOCKING TRIODE THYRISTORS
DESCRIPTION
PNPN devices designed for high volume consumer applications such as temperature, light and speed control; process and remote control, and warning systems where reliability of operation is important.
SCR
FEATURES
*Glass-Passivated surface for reliability and uniformity *Power rated at economical prices *Practical level triggering and holding characteristics *Flat, rugged, thermopad construction for low thermal resistance, high heat dissipation and durability
1
TO-126
1:CATHODE
2:ANODE
3:GATE
ABSOLUTE MAXIMUM RATINGS (Tj=25C unless otherwise noted.)
PARAMETER
Peak Repetitive Forward and Reverse Blocking Voltage (note 1) (Tj=110C, RGK=1k) MCR106-6 MCR106-8 RMS Forward Current (All conduction Angles) Average Forward Current (TC=93C or TA=30C) Peak Non-repetitive Surge Current (1/2 Cycle, 60Hz, Tj=-40 to +110C) Circuit Fusing Considerations (t=8.3 ms) Peak Gate Power Average Gate Power Peak Forward Gate Current Peak Reversed Gate Voltage Operating Junction Temperature Range Storage Temperature Range
SYMBOL
VDRM, VRRM
MAX
UNIT
V
400 600 4 2.55 25 2.6 0.5 0.1 0.2 6 -40 ~ +110 -40 ~ +150
IT(RMS) IT(AV) ITSM It PGM PG(AV) IGM VRGM Tj Tstg
2
A A A A2 W W A V C C
Mounting Torque (note 2) 6 In. lb. Note 1: VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage of the devices are exceeded.
UTC
UNISONIC TECHNOLOGIES CO., LTD.
1
QW-R301-001,A
UTC MCR106
SCR
Note 2: Torque rating applies with use of compression washer (B52200-F006 or equivalent). Mounting torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Anode lead and heatsink contact pad are common. For soldering purposes (either terminal connection or device mounting), soldering temperatures shall not exceed +200C. For optimum results, an activated flux (oxide removing) is recommended.
THERMAL CHARACTERISTICS
PARAMETER
Thermal Resistance, Junction to Case Thermal Resistance, Junction to Ambient
SYMBOL
RJC RJA
MAX
3 75
UNIT
C/W C/W
ELECTRICAL CHARACTERISTICS (Tc=25C and RGK=1000 unless otherwise stated)
PARAMETER
Peak Forward or Reverse Blocking Current (VAK=Rated VDRM or VRRM) Tj=25C Tj=100C Forward "On" Voltage (ITM=4A peak) Gate Trigger Current (continuous dc) (Note) (VAK=7V, RL=100) (VAK=7V, RL=100, Tc=-40C) Gate Trigger Voltage (continuous dc) (VAK=7V, RL=100, Tc=25C) Gate Non-Trigger Voltage (VAK=Rated VDRM, RL=100, Tj=110C) Holding Current (VAK=7V, Tc=25 C) Forward Voltage Application Rate (Tj=110C) Note: RGK current is not included in measurement.
SYMBOL
IDRM,IRRM
MIN
TYP
MAX
10 200
UNIT
A A V A
VTM IGT
2
200 500 VGT VGD IH dv/dt 10 0.2 5 1 V V mA V/s
CURRENT DERATING
UTC
UNISONIC TECHNOLOGIES CO., LTD.
2
QW-R301-001,A
UTC MCR106
SCR
UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
UTC
UNISONIC TECHNOLOGIES CO., LTD.
3
QW-R301-001,A

▲Up To Search▲

Price & Availability of MCR106

	To Download MCR106 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .